LINEARER STROMSENSOR CSLA1DG Honeywell NEU 1 Stück

LINEARER STROMSENSOR CSLA1DG Honeywell  NEU 1 Stück
Preis: €9,99 ( inkl. MwSt. und zzgl. Versandkosten )


Zustand: Neu

Lieferzeit in Deutschland: 2-3 Werktage nach Zahlungseingang (Europa 7-10 Tage, Welt: ca. 3 Wochen)
Artikelstandort: Geestland, Deutschland
Versand nach: Weltweit
Artikelnr.: 15003-007
LINEARER STROMSENSOR
CSLA1DG
Honeywell
1 Stück
Neu



Artikelnummer: 15003 - 007

Sie erwerben 1 Stück
LINEARER STROMSENSOR
CSLA1DG
Honeywell
1 Stück
Neu


Honeywell Stromsensoren bieten genaue und schnelle Reaktionen, für eine Vielzahl von Anwendungen.  Unsere magnetresitive Technologie hat fast keinen thermischen Drift. Die Serie umfasst einstellbar linear, null Gleichgewicht, digitale und lineare Stromsensoren.

FEATURES
1 Linear output
1 AC or DC current sensing
1 Through-hole design
1 Fast response time
1 Output voltage isolation from input
1 Minimum energy dissipation
1 Maximum current limited only by
conductor size
1 Adjustable performance and built-in
temperature compensation assures
reliable operation
1 Accurate, low cost sensing
1 Operating temperature range –25 to
85°C
1 Housing: PET polyester

LINEAR CURRENT SENSORS
MICRO SWITCH CS series linear current
sensors incorporate our 91SS12-2 and
SS94A1linear output Hall effect transducer
(LOHETTM). The sensing element is assembled
in a printed circuit board mountable
housing. This housing is available in
four configuration as shown in mounting
dimension figures 1, 1a, 2 and 2a. Normal
mounting is with 0.375 inch long 4-40
screw and square nut (not provided) inserted
in the housing or a 6-20 self-tapping
screw. The combination of the sensor,
flux collector, and housing comprises
the holder assembly. These sensors
are ratiometric.

Linear Current Sensors 3-Pin

Manufacturer: Honeywell
Part No: CSLA1DG

GENERAL INFORMATlON
CS Series current sensor holder assemblies
have a single linear output that will
source current. The output voltage, which is
ratiometric, varies in direct proportion to the
supply voltage. (Refer to Catalog 20 for
more information). These sensors will not
be damaged by overcurrent in the sensed
conductor.
NORMAL MOUNTlNG
Bottom mount version:
0.375 inch long 4-40 screw and a square
nut (not provided) inserted in the housing.
Side mount version:
0.250 inch long 6-32 screw and a square
nut (not provided) inserted in the housing.

SOLDERING INSTRUCTIONS
Hand Soldering - Use 60/40 rosin core
solder, employing a 399°C (750°F)
controlled temperature, 1/8" chisel tip
soldering iron. To avoid delamination of the
terminals from the ceramic, do not hold the
iron on the terminals for more than four
seconds. The temperature of the lead at the
ceramic conductor interface must not
exceed 250°C (482°F).
Wave Soldering - Use Loncoflux 106A35
or equivalent. Preheaters should be set for
95°C (200°F) on top (component side) of
printed circuit board just prior to board
entering wave. (This may have to be
adjusted depending upon board thickness.)
Solder temperature should be a maximum
of 260°C (500°F), preferably 252°C to 260°C
(485°F to 500°F). Set conveyor speed to
approximately 4.5 feet per minute (1,37
meter/min.). Select a speed which gives full
solder fillets and minimum of bridging and
icicles. The printed circuit board requires
rigid support during wave soldering.
CLEANING
Proper cleaning fluids should be selected
based on the type of contaminants to be
removed. MICRO SWITCH recommends
alcohols, chlorinated solvents, and
fluorinated solvents.
Electrical- Do not exceed maximum supply
ratings. Do not reverse supply voltage
polarity.
Handling -The terminals are fragile.
Handle with care.
Dielectric Isolation- The toroidal cores are
conductive. The user must provide the
necessary dielectric isolation.
MOUNTING DIMENSIONS(for reference only)
WARRANTY/REMEDY
Seller warrants its products to be free from defects in design,
material and workmanship under normal use and service. Seller will
repair or replace without charge any such product it finds to be so
defective on its return to Seller within 18 months after date of
shipment by Seller. The foregoing is in lieu of all other expressed
or implied warranties (except of title), including those
of merchantability and fitness for a particular purpose. The
foregoing is also purchaser's sole remedy and is in lieu of all other
guarantees, obligations, or liabilities or any consequential,
incidental, or punitive damages attributable to negligence or strict
liability, all by way of example.
For application assistance, current specifications or technical help,
call toll free 800/537-6945.
While we provide assistance on MICRO SWITCH products,
personally and through our literature, it is up to the customer to
determine the suitability of the product in the application.

Versandgewicht ca.: 0,060 Kg
Kürzlich angesehene Produkte